• Model NO.：X098ASK
• Origin：Huizhou, China

Basic Info.

Model NO. X098ASK Origin Huizhou, China

Product Description

The model X098ASK is a 1-piece air compressor/tank combination. It is designed for light-duty, intermittent use, such as operating air horns or filling air lockers. It is not designed for heavy duty use such as running air tools or inflating tires.

Specifications:
duty cycle: 9% @ 100 psi
flow rate: 1.27 cfm @ 0 psi
max working pressure: 120 psi
volt: 12v
max amp draw: 12a

Accessories:
0.8 gallons (3 liters) air tank
1/2" npt port compression fitting for 3/8"Φ air line
pressure switch: 85 psi on / 105 psi off
1/4" npt stainless steel braided leader hose

Performance Data:

PSI	CFM	LPM	A
0	1.27	36.0	9
10	1.06	30.0	10
20	0.92	26.0	11
30	0.85	24.0	11
40	0.81	23.0	12
50	0.78	22.0	12
60	0.74	21.0	12
70	0.71	20.0	13
80	0.67	19.0	13
90	0.64	18.0	13
100	0.60	17.0	12
110	0.53	15.0	11
120	0.46	13.0	11
130	0.42	12	11
140	0.35	10	10
150	0.32	9	10

The X098ASK comes to you pre-assembled and prewired. It has a pressure switch that will automatically turn the compressor on when the pressure in the tank drops below 85 psi. It will turn the compressor off when the tank pressure reaches 105 psi. Please note that the pressure switch has a tolerance of +/-5%.
The X098ASK also has a pressure gauge pre-installed. The gauge will show the pressure inside the tank. Please note that the gauge has a tolerance of +/- 5%.
The compressor in the X098ASK system has a 9% duty cycle. This means that you can run the compressor for up to 3 minutes at a time, then it must cool for 27 minutes. Typical fill time from empty is about 1.5minutes, so you can fill and drain it twice before it needs to rest and cool. Performing tasks such as tire inflation that require extended run times will damage the compressor. This type of damage is not covered by warranty. Use the drain cock on the bottom of the tank to periodically drain condensation.

Parts List:
Qty 1  X098ASK Compressor
Qty 1  Mounting Hardware Pack (bolts, nuts, washers)
Qty 1  Compression Outlet Fitting
Mounting the Compressor
The compressor can be mounted upright or on its side. Do not mount it upside-down. Choose a location that will not bring it into direct contact with water, dirt or debris. Be sure to select an area that gets good air circulation to allow the compressor to cool. Use the nuts and bolts provided.
Make sure to secure all four mounting points to a solid metal surface. The compressor does not require lubrication.

Connecting the Air Line
The X098ASK air outlet uses a brass compression fitting designed for ¼" OD nylon air tube (not included). To attach the air line, remove the nut from the compression fitting and slide it over the end of the tube with the threaded side facing the base of the fitting. Push the end of the tube over the center barb of the fitting base, then thread and tighten the nut into place.

Wiring Overview
The X098ASK operates on 12 volts DC. We strongly recommend you wire the system so that it only gets power when the vehicle ignition is on. If you wire the compressor directly to the battery and a leak should occur while the car is parked, the compressor will run continuously until either the battery is drained, or the compressor burns out. We suggest you use one of these two wiring methods:
1. Connect the red power input wire directly to a switched power source. This is a power source that provides 12VDC only when the vehicle ignition is on. Many vehicles will have open, unused circuits in the fuse box that you can use. Make sure any circuit you choose is rated for at least 20 amps. Use a 20-amp fuse (not included) on the X098ASK re power input.
2. (Best Method) Supply power to the X098ASK directly from the battery using a relay that is controlled by the ignition switch.
3. Regardless of the wiring method, make sure the black ground wire from the X098ASK is securely affixed to a metal surface that is clean and free of paint, grease or dirt.